Sales, Information, and Customer Support

Note: Please enable Javascript to use this contact form. Learn how here.

Contact us 1.866.835.6595 Düraamen

decorative concrete and resinous flooring systems

Concrete Crack Repair

Perdüre ECF | 100% solids epoxy crack filler

Perdüre ECF is a 100% solids epoxy crack filler used to line, patch, or repair floor and wall surfaces. Perdüre ECF is the ideal material for repair of surfaces damaged from environmental or chemical attack. It can also be used as a base material beneath coating, slurry, and mortar systems to repair before coating.

advantages

  • Easy 1 to 1 mixing ratio
  • Putty consistency provides easy application
  • Low odor during application and cure – can be used in occupied facilities
  • It can be used in both exterior and interior applications

Technical Data

Mixed Consistency Putty Pot Life 20–30 minutes @ 75°F
Mixing Ratio 1 parts A to 1 parts B by volume Dry to Touch 3–5 hours @ 75°F
Solids Content 100% by volume Re-Coat 4–6 hours @ 75°F
VOC 0 Sanding time 12– 14 hours @ 75°F
Color Gray Full cure & maximum resistance 5 days
Weight Per gallon 15 – 16 pounds per gallon, mixed
top of page

Perdüre CR | polymer modified concrete repair compound

Perdüre CR is a single component, polymer modified concrete repair compound designed for filling and repairing concrete and masonry surfaces above, on or below grade. It is suited for patching and/or resurfacing distressed horizontal surfaces. It is intended for fast turnaround repairs and contains a special migratory corrosion inhibitor. When mixed with water, it results in a consistent mix that can be troweled, shaped and shaved after the initial set.

Perdüre CR is a general purpose concrete repair material used to fill spalls, gouges, dormant cracks and other low areas in existing concrete surfaces, including sidewalks, patios, plazas, courtyards, walkways, driveways, parking garages and pool decks. It can also be used to re-form concrete steps, pre-cast products, concrete pipe, curbs, sidewalks, bridges, panels and walls. It also can be used to fill honeycombs, form tie rise holes, spalls or irregularities due to misaligned forms or unconsolidated concrete. Once applied and allowed to dry properly, Päram, Sgraffino or Überdek can be installed over the entire area to create a desired appearance.

advantages

  • Single component—just mix water on site
  • Specialty polymers promote excellent bond to the existing concrete substrate
  • Can be applied vertically and on overhead applications
  • Tenacious bond to concrete substrates
  • Excellent freeze/thaw stability
  • Quick turnaround, ready for foot traffic in two hours
  • Suitable for residential and commercial applications

Technical Data

Freeze/Thaw Resistance (ASTM C 666 Method B) After 300 cycles 1% loss due to slight scaling; no spalling Shear Bond Strength (ASTM C882) 7 days 1650psi
Shelf life 12 months Shear Bond Strength (ASTM C882) 1 day 1035psi
Mixing water 4.0 – 5.0quarts of water for 50lb bag Compressive strength (ASTM C 928) 28 Days 6500psi
Final set 30 min @ 72°F Compressive strength (ASTM C 928) 7 Days 5845psi
Initial set 20 min @ 72°F Compressive strength (ASTM C 928) 1 Day 4885psi
Flexural Strength (ASTM C348) 28 days 1180psi Compressive strength (ASTM C 928) 3 hours 3340psi
Flexural Strength (ASTM C348) 1 day 1142psi Compressive strength (ASTM C 928) 1 hour 1925psi
top of page

Knowledge & Inspiration